Skip to content
BFCM Sale! Code: BFCM26 for 5% OFF sitewide | DeWalt Workwear 15% OFF | Kress Deals: Save Up to $2,407! Shop Now
BFCM Sale! Code BFCM26 for 5% OFF
DeWalt Workwear 15% OFF
Kress: Save Up to $2,407! Shop Now

Marina and Boat Hardstand Pressure-Wash Parameters

Set pressure by surface, keep hot water for oily work, and contain every litre of runoff.

Shop now
Kranzle Therm 895-1 400V Hot Water High Pressure Cleaner 2830psi 15 L/min - Cleaners
Posted on by John Wei

Two boats come out of the water on the same Sydney hardstand on the same morning. The first is a fibreglass cruiser with soft slime and light barnacle growth over a hull that was antifouled last season. The second is a workboat with diesel staining around the engine bay and grease on the deck fittings. One pressure washer, one operator, and two completely different jobs, each with its own damage risk and its own wash-water problem.

What pressure-wash parameters suit a marina or boat hardstand?

On a boat hardstand, set parameters by surface and soil: a wide fan, generous distance and adjustable pressure on gelcoat; hot water only for oily areas; and all runoff captured on a sealed hardstand draining to a collection system. Antifoul residue is a registered pesticide in NSW, so containment matters as much as cleaning.

Marina and Boat Hardstand Pressure-Wash Parameters

Freshway's guide to fleet wash and transport depots covers vehicle wash bays. This article answers the questions marina and boatyard operators ask about hulls, decks and antifoul wash-water.

How do gelcoat and antifoul soils differ?

Above the waterline, gelcoat and paint carry salt, bird droppings, exhaust film and grime. Below it, the soil is marine growth sitting on, or embedded in, antifoul coating. The NSW Government's cleaning boats fact sheet describes out-of-water cleaning by scraping or water blasting to remove larger organisms such as barnacles and algae, ideally every 12 to 24 months, and says antifoul treatments are a registered pesticide under the Pesticides Act 1999 that must be contained to prevent discharge into waterways.

That changes the goal on the bottom half of the hull. You are removing growth, not stripping coating, unless the job is a planned antifoul removal. Anything the jet takes off below the waterline ends up in the wash-water, so the more aggressive the setting, the more coating you have to capture.

What parameter windows avoid damage?

No Australian regulator publishes a bar figure for gelcoat, and Freshway will not invent one. The safe method is procedural. Start at the lowest adjustable pressure with a wide fan nozzle, hold the lance well back, keep the jet moving and at an angle, and test a small, low-visibility area first. Increase pressure only if the soil will not shift. If the boat builder or coating maker gives a limit, follow it.

Know the energy you are working with. WorkSafe Victoria's high-pressure water jetting alert summarises AS 4233.1: Class A systems have an output capability of 800 to 5600 bar litres per minute, and Class B systems exceed 5600. Multiply bar by L/min from the Freshway page:

Machine (Freshway listing) Pressure Flow Bar × L/min AS 4233.1 class
Kranzle Therm 895-1 hot water, 415 V 195 bar (adjustable) 15 L/min 2,925 Class A
Kranzle Quadro 599TST cold water, 240 V 15 A 150 bar (adjustable) 10 L/min 1,500 Class A

Both sit within Class A, but 2,925 bar·L/min is still enough energy to injure an operator and mark a soft surface held too close. Adjustable pressure is the useful feature here: turn it down for topsides and up only for stubborn growth on a sound antifoul.

How do we contain wash water on the hardstand?

This is where marinas are judged. The NSW EPA's fact sheet on antifouling paints at marinas says it is an offence to pollute waters under the Protection of the Environment Operations Act 1997, and lists working on a hardstand over a catch drain so all waste is captured, tarpaulins on slip rails and a floating boom around the slipway among the ways to reduce risk. The EPA's guidance on preventing contamination on marina sites adds that sealed hardstands should be used for antifouling and repairs, and that work areas should drain inward to a collection system, not to stormwater.

For a pressure washer, that means three practical rules. Wash only on the sealed, bunded area. Keep the catch drain and any pits clear before you start. Never point the jet towards open water or a stormwater grate. The EPA's general rule, the drain is just for rain, applies on every hardstand.

Kranzle Therm 895-1 hot water pressure cleaner for boat hardstands in Sydney
Kranzle Therm 895-1, listed at 195 bar, 15 L/min, up to 150°C, 415 V 20 A three-phase, a 35 litre fuel tank and 223 kg.

When is hot water worth it on boats?

Hot water earns its place on oily work: engine bays, bilge areas, trailers, winches and greasy deck hardware. Freshway lists the Kranzle Therm 895-1 for removing grease, oil and grime, with water up to 150°C (steam level 155°C), a 15 L/min flow, a high-pressure detergent system, a water inlet filter, flame monitoring and low-fuel cut-off. It needs a 415 V 20 A three-phase supply and weighs 223 kg, so it suits a fixed or semi-fixed position on the hardstand rather than being wheeled down a pontoon.

On gelcoat and antifoul growth, start with cold water and add heat only where oily soil is present; hot water also adds a burn hazard on a busy slipway. Keep detergents to a minimum: the NSW Government's boating waste guidance asks owners to minimise chemicals and degreasers, use low- or no-phosphate cleaners and highly diluted solutions, and use an approved slipway or wash bay with waste containment.

Mobile or fixed bay?

A fixed bay suits a yard that hauls boats every day: one sealed area, one drainage path, one set of controls. A mobile cold-water machine suits smaller yards and dry-stack facilities where boats are washed in place on a contained pad. Freshway lists the Kranzle Quadro 599TST at 150 bar and 10 L/min on a 240 V 15 A circuit, with a built-in 10 litre water tank to buffer a weak supply, a 20 metre steel-braided hose on a reel, a D12 quick-release system and a 62 kg four-wheel trolley. A 15 A outlet is required, so confirm the hardstand supply before you buy. Other options are in the commercial pressure washers collection.

Kranzle Quadro 599TST 240 V cold water pressure washer with hose reel for marina wash pads
Kranzle Quadro 599TST, listed at 150 bar, 10 L/min, 240 V 15 A, a 10 L buffer tank, 20 m hose reel and 62 kg.

What should a marine-duty spec include?

  • Adjustable pressure, so topsides and antifoul get different settings.
  • A wide fan nozzle in the kit, plus a rotary nozzle only for stubborn growth on sound coating.
  • An inlet filter, because yard water can carry grit.
  • Enough hose to reach both ends of the hull without dragging the machine through runoff.
  • The right electrical supply for the machine you choose: 240 V 15 A or 415 V three-phase.

Nozzles, lances and fittings are in the pressure washer accessories collection, and the wider range is in Kranzle pressure washers.

Which damage patterns should we brief against?

Without inventing statistics, the risks are predictable from the method: a narrow jet held too close to gelcoat or decals; pressure lifting caulking, sealant or teak plugs on deck; water forced past hatch and window seals; antifoul stripped where the job was only meant to remove growth; and overspray drifting onto neighbouring boats. Record the boat's condition before washing with photos, and agree the scope in writing, so what was already there is not confused with what the wash did.

What goes in the operator briefing?

Brief every operator on the containment rules, the settings for each surface, and personal safety. NSW Resources' fluid injection safety alert describes an injury where a jetting gun's shut-off failed, with unfiltered supply water and uncapped quick-release couplings listed as possible contamination causes. Cap couplings, filter the supply, wear the right PPE and never point the lance at anyone.

Frequently asked questions

Isn't higher pressure faster for barnacles?

It can be, but it also strips antifoul and marks gelcoat. Start low, test a patch and increase only if needed.

Can we rinse boats over the grass at the edge of the yard?

No. Antifoul residue must be contained. Wash on a sealed hardstand draining to a collection system.

Don't we need hot water for every boat?

No. Use hot water for oily engine bays and hardware. Cold water handles growth and topsides.

Is our machine a Class B system?

Multiply listed bar by L/min. Above 5600 is Class B under AS 4233.1; both Kranzle examples here are Class A.

Supplied across NSW, VIC and QLD

Match settings to the surface, then contain every litre. Freshway supplies commercial and hot water pressure washers to businesses in Sydney NSW, Melbourne VIC and Brisbane QLD. Same-day delivery is available in Sydney, with fast delivery to Melbourne and Brisbane. Call 1300 567 002 for a delivered quote, or browse hot water pressure washers.

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare