Skip to content
BFCM Sale! Code: BFCM26 for 5% OFF sitewide | DeWalt Workwear 15% OFF | Kress Deals: Save Up to $2,407! Shop Now
BFCM Sale! Code BFCM26 for 5% OFF
DeWalt Workwear 15% OFF
Kress: Save Up to $2,407! Shop Now

Light-Vehicle Wash Specs for Mining and Industrial Depots

Flow sets supply, runoff and separator load, so spec a depot wash from litres per minute.

Shop now
Nilfisk Magnum PP6012MAG-35HG hot water petrol pressure washer with diesel heater delivering 3500 PSI and 21 L/min for powerful industrial cleaning applications
Posted on by John Wei

21 litres a minute. That is the listed flow of the Nilfisk PP6012MAG-35HG hot-water skid, and it decides more about a light-vehicle wash bay than the pressure figure printed on the side. Flow sets your water supply, your runoff volume and your separator load. For mining and industrial depots buying from Sydney, Melbourne or Brisbane, start the spec there.

What pressure washer specs suit a mining light-vehicle wash?

A mining light-vehicle wash suits a high-flow industrial machine fed by a water supply at least 20% above its rated flow, with hot water for grease and diesel film. Pair it with a bunded bay that drains to an approved oil-water separator, filtered inlet water, and controls for high-pressure injection risk before choosing pressure.

Light-Vehicle Wash Specs for Mining and Industrial Depots

This guide is written for the person buying for a depot or site: how to compare machines, what to ask the wash bay designer, and the steps to set up a workable wash.

LV wash vs heavy plant

Light vehicles such as utes and four-wheel drives need a different approach to dozers and haul trucks. Painted panels, seals, badges and electrical fittings are closer to the nozzle, so the operator controls distance and angle more than raw pressure. A heavy plant wash bay is designed around bulk mud removal. If one bay must serve both, plan for the heavier soil load on the separator and the drains.

Mud, clay and ore dust

Clay and ore dust cling to wheel arches, chassis rails and underbody guards. Flow does the flushing; pressure loosens the soil. A pre-soak with detergent and a wait before rinsing helps loosen dried mud without forcing the lance closer to paint. Keep the nozzle moving, and keep it away from seals, radiators and electrical connectors.

Comparing two machine types

Item Nilfisk PP6012MAG-35HG skid Kärcher HD 9/23 De
Listed pressure 3500 PSI (240 bar) 3335 PSI (230 bar)
Listed flow 21 L/min 400–900 L/h (up to 15 L/min)
Hot water Diesel-fired burner, up to 120°C Cold water only
Engine Honda GX630 petrol Honda GX 270 diesel, 6.3 kW
Fuel 2 × 45 L tanks (petrol and diesel) 5.3 L diesel tank
Supply at 20% above flow about 25 L/min about 18 L/min

Specifications are from Freshway's product listings. Check site rules on fuel types before choosing, because some sites restrict petrol engines.

Nilfisk PP6012MAG-35HG hot water skid for mining light-vehicle wash bays in Brisbane
Nilfisk PP6012MAG-35HG skid, listed at 3500 PSI (240 bar), 21 L/min, with a diesel-fired burner up to 120°C.

Recycled and harsh water effects on pumps

Spitwater's guide to water inlet set-up says supply should be at least 20% more than the machine's rated flow, lists 25 L/min as the minimum for a 21 L/min machine, and warns that bore water can contain minerals or grit that damage components if not filtered. Treat recycled wash water the same way: filter it, and ask the recycling system supplier what quality it delivers before you connect a pump.

Hot water for grease

Diesel film, hydraulic oil and grease release more readily with heat. The PP6012MAG-35HG's burner lets you heat water on site without mains power. A cold-water machine such as the HD 9/23 De relies more on detergent and dwell time. Whichever you choose, heat and detergent both end up in the runoff, so the separator and trade waste approval must allow for them.

Runoff, separators and approvals

Water Corporation's guidance on vehicle and machinery wash-down areas says wash-down areas linked to mining machinery may require pre-treatment and metering, and that sites must have an accepted oil-water separator or other accepted fixture. Sydney Water lists truck and bus washes among activities likely to produce industrial trade wastewater. The NSW EPA's drain is just for rain guidance says stormwater flows into rivers and creeks untreated, and it is against the law to let material flow into a waterway and cause pollution. Check your local water authority's rules for your site.

Throughput of depot queues

Flow sets water use. At 21 L/min, every 10 minutes of trigger time uses about 210 litres. At 15 L/min, the same time uses about 150 litres. Multiply by the vehicles you wash per shift to estimate the volume your separator, recycling system or trade waste consent must handle. Time your own washes on a few vehicles before relying on the figure.

Injection risk and operator controls

WorkSafe Victoria's high-pressure water jetting alert lists the water jet piercing the skin, flying debris and a flailing hose among the main risks. A NSW Resources safety alert describes a fluid injection at a coal plant after a jetting gun failed to shut off, citing unfiltered supply water and uncapped couplings among the causes. Filter the inlet, cap couplings in storage and train operators.

Kärcher HD 9/23 De diesel cold water pressure cleaner on steel frame
Kärcher HD 9/23 De, listed at 3335 PSI (230 bar) and 400–900 L/h with a Honda GX 270 diesel engine.

Setting up the wash: step by step

  1. Confirm the bay drains to an approved separator and that you hold the right trade waste approval.
  2. Measure supply flow at the inlet and confirm it is at least 20% above the machine's rated flow.
  3. Fit an inlet filter, especially on bore, tank or recycled water.
  4. Check site rules on fuel type and fuel storage.
  5. Pre-soak, wait, then rinse from the top down, keeping distance from seals and electrics.
  6. Record maintenance, filter changes and operator training.

Maintenance in dusty yards

Dust gets into air filters, couplings and fuel. Clean inlet filters often, cap couplings when stored, and keep fuel containers sealed. Follow the service intervals in the operator manual for the engine, pump and burner.

Compare options in the industrial pressure washers, diesel pressure washers and hot water pressure washers collections, and the pressure washer accessories range for lances, nozzles and hoses.

Frequently asked questions

Isn't higher pressure always better for mud?

No. Flow does the flushing. Higher pressure near paint and seals can cause damage without washing faster.

Can I run straight off a site tank?

Only if supply flow is at least 20% above the machine's rated flow. Tank water may need a pump and filter.

Do I need hot water for light vehicles?

Not always. Hot water helps with grease and diesel film; for dust and mud, cold water with detergent may be enough.

Can wash water go into the stormwater drain?

No. Wash water should go through approved pre-treatment to sewer or a recycling system, per your local authority.

Delivery to Sydney, Melbourne and Brisbane sites

Spec the water first, then the machine. We offer same-day delivery across Sydney and fast delivery to Melbourne and Brisbane. You can also collect from 208 Princes Highway, Arncliffe NSW 2205 by prior arrangement. Browse commercial pressure washers or call 1300 567 002.

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare